Vinga CS213B black
 |
 |
Relatively inexpensive case with great gaming potential. The MidiTower platform will easily accommodate any of the motherboards: ATX, Mini-ITX, microATX. Thanks to its good capacity, the case can easily fit discrete graphics up to 315 mm long, as well as a processor cooling tower up to 154 mm high. Although the Vinga CS213B case is not equipped with standard fans, it has mounts for 6 120 mm bladed impellers inside: you can put either 3 120 mm coolers or 2 140 mm impellers in the front.
Perforations with dust protection are provided at the front, top and bottom. At the base of the platform there is a compartment covered with a casing, where both an ATX-compatible power supply and a hard drive rack fit. In total, the case has space for 3 3.5″ HDD devices and 3 solid-state SSD drives. The front panel has an embossed protrusion that gives the case a more aggressive gaming character. The right side is made from a single sheet of lightly tinted acrylic. Convenient cable management is provided for neat wiring. The legs of the case are rubberized, which eliminates the vibration load on the countertop.
Buy Vinga CS213B black
All prices 29 →Корпус Vinga CS213B | 1 189 ₴ |  | |||
| 1 189 ₴ |  | ||||
| 1 388 ₴ |  | ||||
| 1 189 ₴ |  | ||||
Vinga CS213B | 1 189 ₴ |  | |||
I came to ITbox with two big scratches on the front panel and in pills. Cheap, compact, good ventilation to the case, backlight, the ability to install two 140mm fans Scratches, pills  Юрій Сорокін: use Vinga CS213B less than month |
Yesterday I assembled a “stove”. It can be said that I didn’t save on “meat”, I took a solid average to last for a long time with a margin for an upgrade. And I took the case cheaper, but not quite for a penny - I regretted it a little. I rate it as a good model. But really, it's somewhere between good and nothing special. Too bad there isn't one on the site.
The case is futuristic with RGB LED stripes on the front panel (there is a mode change button on top of the case). The case itself is made of thin steel and brittle plastic. Dust filters front and top. Glass viewing window (a plus here). Included was a bag with a handful of screws. Without instructions, which is bad because it is not immediately clear where which screw is, plus this is the first time in my life I have assembled a computer. Standoffs have already been installed. Plugs under the board must be broken out. There is no sled for the HDD, plus you need to install it first, since you need to twist it from the side of the power supply unit and with the front panel removed. Everything fell into place without any problems, which cannot be said about USB 2.0 connectors and sound. Flimsy, the plugs themselves hang out in plastic and it is clear that they are not even. They enter very tightly, they just don’t go, I couldn’t deliver, I didn’t want to break the board. Fortunately, I was able to connect power, light bulbs, USB 3.0 and Molex backlights. The body is well ventilated, there is ventilation on all sides. Housing with rubberized feet, at a height of 20 mm from the surface. The PSU has a place to take air from, plus it also has a dust filter. It's a shame that one fastening of the front panel from the bottom broke off. - stylish;
- blown with dust filters; - Nice LED front lighting; - viewing window made of glass; - PSU from below; - minimal cable management can be arranged. - thin steel, brittle plastic;
- tight connectors; - lack of at least minimal instructions; - plugs for boards break out; - no sled for HDD.  Валентин К.: use Vinga CS213B less than month |
